finaly finished my W/C

[DarthBeavis]

and where do u live btw?

[xo4ox]

in Saudi Arabia

[blue_fire]

You might need more pressure on the cpu. get into bios, go to your temperature monitoring, and slowly tighten all of the bolts down little by little and see if you temp drop. NG hpnotic is getten better temps than that with a single 120 rad and a 305 at 3.5ish

[xo4ox]

i will try and get back to you, i also think my GPU temps are wierd, its 50c idle and 63c full load and my NB is 37c

[blue_fire]

Uh are those stock speeds for the ultras? too much/not enough paste? AS5? all of this will help us.
Also drop your multi and raise your fsb if you can. Did that to me E4300, and was able to lower vcore almost back to stock at 2.8ghz

[V2-V3]

What is your CPU voltage?

as for your 8800Ultra's I have that same water block on mine and i hold 42c Idle and about 55c load.

I checked on 5 other 8800's w/ the koolance block and they all are all 40-45c idle and 55-60 load.

the only two things i can see effecting your temps would be the water loop flow path and thermal paste.

also the tubing between both 8800 can be replaced w/ a sexy 3 slot koolance interconnect nozzle.
Dual VID Connect Nozzle, 3 Slot Spacing - Water cooling systems, pc liquid cooling kit, cpu, video card, hard drive


We have a QX6800 running with a CPU-330 block in our office and ill take a look at the temps a little later.

[xo4ox]

Originally Posted by blue_fire

You might need more pressure on the cpu. get into bios, go to your temperature monitoring, and slowly tighten all of the bolts down little by little and see if you temp drop. NG hpnotic is getten better temps than that with a single 120 rad and a 305 at 3.5ish

it didnt work

Originally Posted by blue_fire

Uh are those stock speeds for the ultras? too much/not enough paste? AS5? all of this will help us.
Also drop your multi and raise your fsb if you can. Did that to me E4300, and was able to lower vcore almost back to stock at 2.8ghz

no they are 685/1132, and i placed AS5 and its normal amount (not like the CPU :s) i will try the fsb thing and write back.

Originally Posted by V2-V3

What is your CPU voltage?

as for your 8800Ultra's I have that same water block on mine and i hold 42c Idle and about 55c load.

I checked on 5 other 8800's w/ the koolance block and they all are all 40-45c idle and 55-60 load.

the only two things i can see effecting your temps would be the water loop flow path and thermal paste.

also the tubing between both 8800 can be replaced w/ a sexy 3 slot koolance interconnect nozzle.
Dual VID Connect Nozzle, 3 Slot Spacing - Water cooling systems, pc liquid cooling kit, cpu, video card, hard drive

at stock it is 3.0v i think, i will make sure but im pretty sure its 3.0v, nice to know at least i have the GPUs almost right, and i have that 3 slot connector but i didnt use it so i can include the SB in the loop, and do you mean my loop path is incorrect? if so what do you suggest?

Originally Posted by V2-V3

We have a QX6800 running with a CPU-330 block in our office and ill take a look at the temps a little later.

i would realy appreaciate that and can you tell me what kind of rad and if its a only CPU loop, and also do you think my pump isnt good enugh? or my res is too small?


and finally can some one tell me whats the fans specs on my radiator coz i cant find it anywhere.

[SoundEvolution]

1 word DANGER DEN!!!!

LOL

JOKES JOKES GOOD OLD PDX 10
changing blocks sorry didnt mean to high jack this lol

[xo4ox]

after further investigations i am almost positive that there is no contact between the cpu and the block because when i feel the GPU blocks they are warm even when touching the tubes in the GPU loop its warm too, but when doing the same on the CPU it is cold and also the tubes, so what can i do to fix this? i already tightened the block to the limit and i don't think i can go more without damaging something

[V2-V3]

Originally Posted by xo4ox

after further investigations i am almost positive that there is no contact between the cpu and the block because when i feel the GPU blocks they are warm even when touching the tubes in the GPU loop its warm too, but when doing the same on the CPU it is cold and also the tubes, so what can i do to fix this? i already tightened the block to the limit and i don't think i can go more without damaging something

you can not damage the CPU or mobo from screwing down the block too much (unless you are the hulk or something), at most the system will not post and you can back the screws off a little more till the system posts.

i think anything over 50lb of pressure on the 680I CPU socket and the system will not post.